-40%
4.5KW BT30 ATC Air Cooled Spindle Motor 220/380V 24000RPM Automatic Tool Changer
$ 902.88
- Description
- Size Guide
Description
4.5KW BT30 ATC Air Cooled Spindle Motor 220/380V 24000RPM Automatic Tool ChangerFor CNC Router
Engraving Milling Machine
220V or 380V
Package include:
1 x 4.5KW ATC Air cooled spindle motor 220V
( BT30,24000rpm,4 bearings,800Hz, 220V )
1 x BT30-ER25 Tool Holder
with 45° pull stud
2 x Aviation plug
Note:We also have 380V,if you need,pls contact us before purchase.Default is 220V.
100% Brand New and High Quality!!!
1
)
This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation.
2
)
The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle.
3)The atc spindle uses air cooling to cool the motor and front and rear bearings. The wind is provided by the fan at the rear end, from the rear of the spindle through the inner and outer air slots directly to the front of the spindle, thereby taking away the heat generated by the high-speed rotation of the spindle, achieving thermal balance, and keeping the temperature of the electric spindle within a certain value.
4
)
The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature.
5
)
The tool clamping methods:this spindle built-in automatic tool change device,shank form is BT30.
Product technical parameter table
Spindle
m
odel
:
RTM1
2
0
x103-30
-24Z/
4
.5
220V
Voltage
:
220
V
Maximum speed
:
24
000rpm
Rated frequency
:
8
00
Hz
Electric current
:
15
A
Motor
pole
:
4Pole
R
ated power
:
4.5
KW
(S1)
Peak power
:
5.4
KW
(S6)
Rated torque
:
3.5
Nm
Peak torque
:
4.2
Nm
Product characteristic curve graph:
Wiring
definition:
Power supply, Fhermal, Fan
Proximity switch and push button switch:
Details:
T
echnical
p
arameters
No.
P
roject
Standard
1
Spindle blowing dust/seal gas pressure
(MPa)
0.2-0.25
2
Spindle gas seal gas flow
(
L/min)
65±10
(
When on
Working
)
3
Cooling air fan pressure
(
MPa)
≧
0.25
4
Cooling air fan flow
(
L/min)
≧
2.5
5
Spindle static state pulse
(
µm
)
≦
3
6
Spindle vibration
(
mm/s
)
≦
1.0
7
Spindle assembly method
Bottom mounting
(
6-M8
)
8
Motor windings
Pressure test
(
V/M
)
1000
V/1 minute withstanding Voltage test
9
Tool Interface
BT30
10
Inverter Specifications
5.5
KW
(220
V
)
11
Fitment
Woodworking machinery, polishing industry, etc.
5.
Spindle installation explanation
1)
F
an cooling system description
When the spindle rotates, the rear fan system must be started to ensure the correct supply voltage and the supply voltage is 12V.
2)
Air sealing control
(AS)
In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,t
he gas seal machine must be started start with the machine at the same time.
And the need to go through
multi-stage filtration.
3)
Compressed gas quality requirements
The quality requirement of gas which is used in gas seals:
Oil content
:
﹤0.01mg/m³
S
olid particle
:
﹤5µ m
Pressure dew point
:
﹤7.5℃
(
0.7MPa
)
4)
Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.
Note:
new or spindle
which
is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase
to
50% of the maximum speed,to run 15 minutes,finally,
increase to maximum speed.
It’s n
eed to check the temperature of the spindle
d
uring the whole
process,
spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.
5)
Product backend interface instructions
No.
Function
D
efinition
1
Gas
sealing
(
Protection of impurities into the spindle
0.2-0.25MPa
)
Ф
6
2
Return air
(
piston reset 0.35-0.45MPa
)
Ф
6
5
Power supply
(
Spindle power lines with thermistor
)
U/V/W/ Ground wire
6
Intake air
(
Spindle loose knife
0.5-0.6MPa
)
Ф
6
7
Sensor
(
spindle tool change signals 24V
)
Broach / loose knife
8
Fan (
spindle cooling
)
12V
6)
PTC140
Temperature coefficient thermistor parameters
Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection
.
Parameter name
Parameter symbol
Single core
Three core Series connection
Unit
Maximum DC working temperature
Umax
30
30
V
Rated control temperature
Tk
Designed according to user
℃
Rated control temperature tolerance
T1
±5
℃
±5
℃
℃
Rated control temperature tolerance
T2
±0.5
℃
±0.5
℃
℃
Resistance value on 25
℃
R25
≤
100
≤
300
Ω
Rated control temperature
on -5
℃
resistance value
Tk-5
℃
≤
550
≤
1600
Ω
Rated control temperature
on +5
℃
resistance value
Tk+5
℃
≥
1330
≥
4000
Ω
Rated control temperature
on +15
℃
resistance value
Tk+15
℃
≥
4
≥
12
KΩ
Thermal response time
Ta
≤
5
≤
5
S
Dielectric strength
Uis
AC2.5
AC2.5
KV
Maximum control temperature
Tkmax
180
180
℃
Maximum allowable storage temperature
Tmax
180
180
℃
Minimum allowable storage temperature
Tmin
-40
-40
℃
7
)
Product
Tool Change
Signal
s
Description
Sensor Model (0-24V, PNP),
The spindle built two sensors.wiring Diagram is as follows:
1. Response broach knife signal, when the
knife handle
is hang,
black sensor output signal;
2. Response loose knife signal, when the
knife jaws
open,
black sensor output signal;
2).BT30-ER25 tool holder with 45° pull stud
Payment:
> 1. Payment is needed to receive within 5 days after deal.
> 2. We only accept PayPal.
> 3. PayPal is the only online payment method we accept. Please make sure you have a valid/confirmed PayPal account prior bidding. And please make sure that your PayPal registed address is the same with your eBay registed address.
Feedback:
We maintain hightest buyer ratings
> Positive Feedback will be much appreciated from you.
> Any dissatisfaction,please contact us immediately!
> Please do not leave neutral or negative feedback before we help you out.
Returns:
> Defect: We will fully refund or send you a new replacement,please contact and return within 30 days.
> Dissatisfaction: Please contact within 3 days, we will fully refund, after got your returned goods.
> Missing parts/Q'ty: Please contact us immediately,for a new package arranged,or a partial refund issued.
Contact us:
> If have any question, Please contact us by ebay message before leaving neutral, negative feedback or open any dispute, we will reply within 24hours, ensure that help you solve the problem, make you satisfied.